How to Install: Thoroughly clean the surface (isopropyl alcohol is best). When dry, peel the paper backing from the vinyl sheet and apply. Once vinyl is applied, you can use heat to activate the adhesive (a heat gun or hair dryer and softly press the film into place with a rubber squeegee or by hand) Take a sharp utility blade or razor blade and carefully cut vinyl to shape and peel excess away. The vinyl can be removed at any time with no damage to the vehicle. It also protects the emblem from harmful UV rays and rock chips. Helpful Tips: Apply in temperature that is 50 degrees or more Do not apply in direct sunlight Allow the vinyl 24-48 hours to adhere (preferably in direct sunlight)
Do not touch the adhesive backing of the decal, oils from your skin will prevent sticking.
Do not apply on extreme cold or hot Surfaces. Ideal temperature must be between 60°F & 90°F.
When you first receive your decal: If the graphic(s) release with difficulty from the white/blue wax paper backing, rub the top of the decal with a credit/debit card. This step helps break the bond between the graphic and the wax paper.
NEXT: Hold the decal with the graphic facing you, now from any corner, peel the transfer tape off of the decal. Now you should be holding a graphic fully adhered to the transfer tape.
DRY Application Tips: Decal CANNOT BE adjusted once it is placed
Carefully position the decal to the desired area. – you cannot move your decal once it is placed
Rub the decal starting from the center working out to the sides of the decal, eliminating any air bubbles.
Use an object like a credit card to make sure the entire decal is fully adhered to the surface.
Slowly remove the transfer tape, peeling it at 180º against itself.
Check for air bubbles. In most cases air bubbles can be worked to the edge of the decal, if not, a pin hole will allow the air out and become virtually invisible.
GMC Vehicle Emblem Overlay Kit Application Instructions How to Install: Thoroughly clean the surface (isopropyl alcohol is best). When dry, peel the paper backing from the vinyl sheet and apply. Once vinyl is applied, you can use heat to activate the adhesive (a heat gun or hair dryer and softly press the film into place with a rubber squeegee or by hand) Take a sharp utility blade or razor blade and carefully cut vinyl to shape and peel excess away. The vinyl can be removed at any time with no damage to the vehicle. It also protects the emblem from harmful UV rays and rock chips. Helpful Tips: Apply in temperature that is 50 degrees or more Do not apply in direct sunlight Allow the vinyl 24-48 hours to adhere (preferably in direct sunlight)
Before You Start Clean Your Application Surface First Store Front Application Instructions APPLICATION INSTRUCTIONS Line Up the Decal Where You Would Like It Placed.
Then Place Tape Down The Middle (on the whole decal (both the wax paper backing and the clear transfer tape). Remove The Clear Transfer Tape Away From The Wax Paper Backing. The Decal Should Stick To The Clear Transfer Tape.
Then Cut Away The Exposed Wax Paper Backing - Decal On One Side Of The Hinge.
Then From The Hinge (middle center working to the end) Start Pressing The Decal To The Application Surface Area.
Use A straight Edge To Smooth The Decal To The Surface Complete The Same Steps For The Other Side Of the Decal
Carefully Remove The Transfrer Tape From The Applied Decal, Leaving Your New Decal On Your Application Surface.
WET Application Tips: Decal CAN BE adjusted once it is placed (slightly side to side, not up and down) check on-line for video how to *YouTube* for video instructions
Lightly mist the desired area with application mix, which is (8oz OF WATER MIXED WITH 1-2 DROP OF DISH SOAP LIKE DAWN DISH SOAP).
Use the least amount of fluid to accomplish the application process (1-2 sprays depending on project size). **Spraying cut vinyl letters with fluid can also cause the lettering to loosen up on the transfer tape or cause the lettering to fall off, ONLY SPRAY THE APPLICATION AREA- NOT THE DECAL-
When squeegeeing the graphics, use good pressure to force all of the fluid from under the vinyl film. When using a WET APPLICATION use your FINGERS 1st, then a HARD credit card, if needed. Your fingers have enough pressure to force all the fluid out. Start in the center of the graphic and squeegee outward to force out the fluid from underneath the graphics
If the transfer tape releases with difficulty from the graphics, spray the tape with the fluid mixture allowing about 30 seconds for the fluid to soak in.
In removing the transfer tape, peel the tape 180º against itself.
BOTH WET & DRY APPLICATION - Place Your Decal In Direct Sunlight for 2-3 hours after application – It Adheres The Vinyl Faster!!
It is best to wait at least 24 hours before use (vinyl manufacture suggestion)
Paper Transfer Tape Allows Your decal’s either a WET or DRY application!
For More Great Decals & Custom Decals email: ShopVinylDesign@gmail.com
Graphics must be saved in Vector based file formats. Vector based images are made up of lines and curves and can be resized, and manipulated without losing the quality of the graphic. Vector graphics are defined by a series of mathematical equations and enable us to scale the object to any size without losing any detail or clarity. JPEG and TIFF files are not able to achieve this manipulation.
No Printing Your Vinyl Graphic Decal will not Fade, Run or Bleed
Vinyl Graphic Decals are cut directly from vinyl without ink or printing. Any vinyl occupying the negative space of your graphic is weeded out, creating a dynamic decal perfect for laptops, vehicles, store windows, boards, bikes, trailers and other surfaces.
We offer indoor, indoor-outdoor and marine rated vinyl’s. Not all surface application areas are the same, we will assist you in choosing the correct vinyl for your project. We offer a variety of vinyl colors.
Easy to Apply
Transfer Tape, or Application Masking, keeps all the pieces of your graphic in one place. We offer both paper and clear transparent transfer tape, there is a difference and we will assist you in choosing the best tape for your project. Check out our Dry and Wet Vinyl Graphic Decal Application page.
If you need any assistance click here to contact us
Oracal 651 vinyl, up to 6 year outdoor rated vinyl
Oracal 631 vinyl, safe for indoor walls (drywall)
Click on this link to see a list of our available vinyl's and colors
Sizing is measured to the longest width or longest height (excluding tumbler decals, which are measure by height and stated above).
Example: 6”W x 3”H is a 6” inch decal
Example: 3”W x 6”H is a 6” inch decal
If you need complete sizing W x H and it is not stated in the listing, send us a message and we will send you the complete sizing.
TUMBLER DECAL SIZING/DIMENSIONS
3”H is our Universal Tumbler size.
Shipping is Free on all orders with no minimum purchase. Orders are shipped via USPS, First Class Mail with tracking. You will be notified with a confirmation message and tracking number.
Expedited shipping is available for an additional charge. Orders are packaged carefully to ensure that they arrive to you as safely as possible.
If an order is lost in transit and not marked as delivered, it will be replaced at no cost to the customer.
In the event that a package is not delivered and tracking states that the package was delivered, a refund or exchange will only be offered when the customer completes and files a stolen mail report.
In the event that a package is delivered damaged, please contact us within 3 days of receiving your order, a replacement product will be sent to you (we must receive a picture of your shipment before sending the replacement)
Orders $30 or more will require signature upon delivery.
Please contact us within 24 hours after placing your order. All orders are processed within 24 hours and shipped within 48 hours. We cannot cancel an order after it has shipped. Sizing or color changes will require the original order to be cancelled and a new order will need to be placed.
POLICY FOR CUSTOM ORDERS:
A proof will be sent on all custom orders. You MUST approve the proof sent before we complete your order.
We offer a maximum of 3 “Mock-Up Proof’s”. A charge of $5 will be charged for each additional “Mock-Up Proof”.
Images outside of our “Artwork Requirements”, image(s) can be sent to our Graphic Designer for “Professional Digitization”. The image(s) will be converted to vector images (SVG, AI, EPS, DXF, PNG, JPG, PDF). You will receive a zip file of the vectored images. There is an additional charge for this service. Pricing is based on the quality of submitted images(s) and range from $15 - $25 per image.
Returns are not accepted on custom orders, outside of damage or defect. We must be notified within 3 days of delivery of a received damaged or defected shipment.
If you are not 100% satisfied with your order, please contact us within 3 days of receiving your order. We work quickly to resolve issues. All return inquiries must submit an image of the shipment they received and an explanation as of why a return/exchange is being requested. We offer “Hassle Free” returns and want you to love your new decal(s). No returns on decals that have been used.
Decals that have been placed improperly will not be replaced or refunded. This includes such improper application methods as not cleaning surfaces prior to application, using application devices that scratch or tear the decals, or not applying the decals straight. Please refer to the included application instructions prior to applying decals.
In the event that a return is authorized, the item must be sent with a tracking number. A 25% restocking fee will be assessed. Item must be shipped within 7 business days of return authorization.
We have a three-step process in fulfilling and shipping in place to help ensure that you receive the correct order without defect. If there is something wrong with your order upon arrival, please contact us within 3 days and we will work with you to resolve the issue. Send a picture of your shipment (what you received including invoice) to us when you contact us.
We are located outside of Orlando, FL. We are an on-line webstore.
Email is our preferred method of contact. Our email address is: ShopVinylDesign@gmail.com Or Contact Us